Avalon Astoria Operations Instructions

Browse online or download Operations Instructions for Cookers Avalon Astoria. Avalon Astoria Operating instructions User Manual

  • Download
  • Add to my manuals
  • Print
  • Page
    / 9
  • Table of contents
  • TROUBLESHOOTING
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 0
Pellet Control Board
Installation Instructions 250-00011
Page 1 of 9 Printed 8/13/08
Compatibility
Avalon Newport PS and Newport Bay PI (Avanti PS & PI)
Avalon Astoria PS and Astoria Bay PI
Avalon Arbor PS
Lopi Pioneer PS and Pioneer Bay PI (Heritage PS & PI)
Lopi Yankee PS and Yankee Bay PI
Lopi Leyden PS
Packing List
Control Board
Molex Jumper
Overview
This control board is compatible with all large and small pellet heaters manufactured from 1997. Circuitry on the
board allows it to be programmed for either the large or small pellet heaters (these heaters use different voltage
settings). See “Configuring the Control Board“ for details. It also includes a diagnostic feature that allows the end
user to diagnose common problems without having to inspect the wiring or components. The indicator lights on
the control board will display a maintenance code after a problem has been detected. See “Diagnostic Codes” for
details. NOTE: the new wiring harness (250-00017) is required to utilize this feature.
Configuring the Control Board
Configuring for Large or Small Heaters
The control board is initially configured for the large heaters (Astoria, Yankee, Arbor, and Leyden). To change the
configuration the control board must be in the off position plugged into a cold stove, (no lights or running
components) with the jumper molex removed (see the illustration below). In this condition press and hold the
manual auger button down and press both fan up and fan down arrow keys at the same time. All heat output
lights will flash. One flash denotes the large pellet heater configuration. Two flashes denote the small pellet heater
configuration (Newport and Pioneer models). Repeat pressing the keys until the correct configuration is obtained.
250-00012
Using this Control Board with Older Wiring Harnesses
When the control board is installed on an older wire harness the 4 pin molex jumper plug on the back of the
control board next to the stock wire harness must be installed. This jumper replaces the diagnostic wires (see
“Wiring Diagram”) that are present on the new wiring harness. The control board will work normally, but the
diagnostic capabilities will not function.
Page view 0
1 2 3 4 5 6 7 8 9

Summary of Contents

Page 1 - Pellet Control Board

Pellet Control BoardInstallation Instructions 250-00011Page 1 of 9 Printed 8/13/08Compatibility• Avalon Newport PS and Newport Bay PI (Avanti PS &

Page 2

Pellet Control BoardInstallation Instructions 250-00011Page 2 of 9 Printed 8/13/08Technical Notes for OperationMake sure to give the home owner the “P

Page 3

Pellet Control BoardInstallation Instructions 250-00011Page 3 of 9 Printed 8/13/08Wiring Diagram (new, 2005 version – 250-00017)Large Pellet Stoves On

Page 4

Pellet Control BoardInstallation Instructions 250-00011Page 4 of 9 Printed 8/13/08Wiring Diagram (older version – 100-00393 - B Rev)NOTE: Wire colorin

Page 5 - Troubleshooting Instructions

Pellet Heater Operating andTroubleshooting InstructionsPage 5 of 9 Printed 8/13/08The Two Modes of Operation:ManualManual mode requires the user to tu

Page 6

Pellet Heater Operating andTroubleshooting InstructionsPage 6 of 9 Printed 8/13/08Manual ModeManual mode requires the user to turn the heater on and o

Page 7

Pellet Heater Operating andTroubleshooting InstructionsPage 7 of 9 Printed 8/13/08Auto ModeAuto mode allows you to use a thermostat to control room te

Page 8

Pellet Heater Operating andTroubleshooting InstructionsPage 8 of 9 Printed 8/13/08Adjusting the Fan SpeedAUTOOFFMANUALHEATFANUPDOWNUPDOWNMANUALMANUALS

Page 9

Pellet Heater Operating andTroubleshooting InstructionsPage 9 of 9 Printed 8/13/08"Maintenance Required" LightNOTE: If the “MAINTENACE REQUI

Comments to this Manuals

No comments